ANT: Broadcast TX
The Broadcast examples consists of basic example applications that can be used to test ANT connectivity between a transmitter and receiver.
Overview
This sample uses the ‘’CONFIG_ANT_NP’’ and ‘’CONFIG_ANT_INCLUDE_NP_CHILD_IMAGE’’ Kconfig options to automatically configure a child image for multicore platforms.
Channel configuration
This example uses the default channel configuration:
Parameter |
Transmitter |
Receiver |
|---|---|---|
Channel type |
Master (0x10) |
Slave (0x00) |
Network key |
Public |
Public |
RF channel |
66 (2466 MHz) |
66 (2466 MHz) |
Device number |
0x02 |
0x02 |
Device type |
0x02 |
0x02 |
Transmission type |
0x01 |
0x01 |
Channel period |
8192 (4 Hz) |
8192 (4 Hz) |
Requirements
Hardware platforms |
PCA |
Board name |
Build target |
nRF5340 DK |
PCA10095 |
nrf5340dk_nrf5340 |
nrf5340dk_nrf5340_cpuapp |
Configuration
nRF5340 configuration files
This sample configuration is split into the following two files:
generic configuration (cpuapp) is available in the prj.conf file
configuration for the ant_rpc child image (cpunet) is stored in the child_image subdirectory.
Building and running
This sample can be found under ant/samples/ant_broadcast_tx in the nRF Connect SDK folder structure.
Testing
After programming the sample to your development kit, you can test the Broadcast Transmitter using ANTware II:
Compile and program the Broadcast Transmitter.
Run ANTware II. Select your ANT PC dongle (for example, ANTUSB-m) from the available devices.
Configure the device channel by loading the device profile configuration from the following file:
ant\samples\ant_broadcast_tx\ant_broadcast_tx_test.xml
Alternatively, you can configure the device channel manually:
Set the channel assignment to Slave.
Set the channel ID to “0, 0, 0”.
Click the Auto-Open button. Observe that messages describing the received payload appear for each ANT message. These messages should look similar to the following fragment:
Received BROADCAST_DATA_0x4E :: 4e, 00-00-00-00-00-00-00-00-01 Received BROADCAST_DATA_0x4E :: 4e, 00-00-00-00-00-00-00-00-02 Received BROADCAST_DATA_0x4E :: 4e, 00-00-00-00-00-00-00-00-03 Received BROADCAST_DATA_0x4E :: 4e, 00-00-00-00-00-00-00-00-04 Received BROADCAST_DATA_0x4E :: 4e, 00-00-00-00-00-00-00-00-05 Received BROADCAST_DATA_0x4E :: 4e, 00-00-00-00-00-00-00-00-06
On the nRF DK side, the virtual COM port will show corresponding EVENT_TX messages.
[00:00:00.491,210] <inf> ant_broadcast_tx: ANT Broadcast TX example started [00:00:00.749,725] <inf> ant_broadcast_tx: EVENT_TX - 03 40 00 01 03 [00:00:00.999,725] <inf> ant_broadcast_tx: EVENT_TX - 03 40 00 01 03 [00:00:01.249,725] <inf> ant_broadcast_tx: EVENT_TX - 03 40 00 01 03 [00:00:01.499,725] <inf> ant_broadcast_tx: EVENT_TX - 03 40 00 01 03 [00:00:01.749,725] <inf> ant_broadcast_tx: EVENT_TX - 03 40 00 01 03