You are here: Forum Home → ANT Developer’s Forums → ANT General Questions → Thread
I would like to enable an ANT/BLE capable radio on a Single Board Computer (SBC) running Android. The SBC is to be packaged in a box with one 2.4GHz antenna and should be capable of running APKs that target ANT+ or BLE comms. The final setup would be similar to having an Android phone such as the Samsung S20 where you would be able to run an APK such as the ANT+ Demo (after loading the ANT+ Plugins, ANT Radio & ANT USB services) and gather data from an ANT sensor or communicating with a watch via Bluetooth.
Based on my initial investigation, the Nordic nRF52840 SoC in combination with the SoftDevice S340 could provide the required ANT / BLE radio capabilities to the SBC via a USB 2.0 port.
We put together a setup with the Android SBC using the Garmin ANTUSB-m dongle and were able to get data from a couple of ANT sensors such as the Garmin Tempe. Then, we attempted to replace the ANTUSB-m dongle with the nRF52840 USB dongle but were unable to get ANT to work. We tried programming different examples available from Nordic but only getting the Bluetooth ones to work.
In essence we are trying to make the equivalent of the Garmin ANTUSB-m dongle with Bluetooth capabilities. Eventually, our design would have the nRF52840 placed in a M.2 Key-E card with a U.FL connector.
My questions are the following:
1) Is there a document that would help guide us through the necessary steps to program the nRF52840 using the SoftDevice S340, enabling both ANT and Bluetooth?
2) Is there an example available that we could use or adapt to enable both ANT and Bluetooth in the nRF52840?
geometry dash lite
We are new to ANT, to the Segger Embedded Studio (SES) programming environment and the Nordic tool sets. The advice we got from Nordic’s DevZone was to reach out to thisisant.com. The only medium I was able to find to request help in thisisant.com is this forum. I would appreciate any input that could get us moving forward. Also, any offers on consulting (sent via a private message) to help us getting this done would be considered.
I would like to enable an ANT/BLE capable radio on a Single Board Computer (SBC) running Android. The SBC is to be packaged in a box with one 2.4GHz antenna and should be capable of running APKs that target ANT+ or BLE comms. The final setup would be similar to having an Android phone such as the Samsung S20 where you would be able to run an APK such as the ANT+ Demo (after loading the ANT+ Plugins, ANT Radio & ANT USB services) and gather data from an ANT sensor or communicating with a watch via Bluetooth.
To enable ANT and Bluetooth on the nRF52840 with SoftDevice S340, install Segger Embedded Studio (SES) and download the nRF5 SDK and SoftDevice S340. Use and merge ANT and BLE examples from the SDK, initializing both stacks in your code. For detailed guidance, consult Nordic DevZone or ANT documentation. Last semester, I was drowning in assignments and didn't know how I would finish everything. That's when I found https://domypaper.com/ Their service was a lifesaver! The quality of the work was top-notch, and they delivered on time. If you're a student struggling to keep up, give them a try. You won't be disappointed.
Based on my initial investigation, the Nordic nRF52840 SoC in combination with the SoftDevice S340 could provide the required ANT / BLE radio capabilities to the SBC via a USB 2.0 port.
We put together a setup with the Android SBC using the Garmin ANTUSB-m dongle and were able to get data from a couple of ANT sensors such as the Garmin Tempe. Then, we attempted to replace the ANTUSB-m dongle with the nRF52840 USB dongle but were unable to get ANT to work. We tried programming different examples available from Nordic but only getting the Bluetooth ones to work.
In essence we are trying to make the equivalent of the Garmin ANTUSB-m dongle with Bluetooth capabilities. Eventually, our design would have the nRF52840 placed in a M.2 Key-E card with a U.FL connector.
My questions are the following:
1) Is there a document that would help guide us through the necessary steps to program the nRF52840 using the SoftDevice S340, enabling both ANT and Bluetooth?
2) Is there an example available that we could use or adapt to enable both ANT and Bluetooth in the nRF52840?
geometry dash lite
We are new to ANT, to the Segger Embedded Studio (SES) programming environment and the Nordic tool sets. The advice we got from Nordic’s DevZone was to reach out to thisisant.com. The only medium I was able to find to request help in thisisant.com is this forum. I would appreciate any input that could get us moving forward. Also, any offers on consulting (sent via a private message) to help us getting this done would be considered.
Nordic Semiconductor's website offers the most recent version of the nRF5 SDK for download. You can use the ANT and Bluetooth example projects included in the SDK as a guide for your own implementation.
